MTM Hydro Snow Foam Cannon

Our Price: $69.99
Brand:
MTM Hydro
SKU:
14.0263
UPC:
013964388121
Availability:
Usually ships within 12 hours

MTM Hydro Snow Foam Cannon

The MTM Hydro Snow Foam Cannon is the perfect tool for any car enthusiast who wishes to apply a thick rich coat of snow soap to the paintwork!  By utilizing a foam cannon you are able to deposit the cleansing solution across the surface to loosen and remove dirt, grime, and abrasive particles before you ever touch the paint.  On sensitive surfaces with bonded dirt this can be a key factor in lessening swirls on the surface over time.  Simply attach the apparatus to your pressure washer and pour the desired amount of snow soap into the canister.  

The Original Foam Cannon will now include a 1.1mm/3.0 orifice, along with the pre-installed 1.25mm/3.5 orifice. By switching out the pre-installed orifice (1.25mm/3.5 orifice) with the included orifice (1.1mm/3.0 orifice), it allows you to convert your kit into a low pressure/volume device if needed.

Features:

  • Spray Pattern: Horizontal adjustability 
  • Ergonomically Designed Comfort Grip Bottle: 32 oz Capacity
  • Internal Agitator: Creates dense foam
  • Includes M22 & 1/4" Quick Disconnect connector
  • Range: 1,100 to 4,000 PSI
  • Min.- Max flow: 1.8 - 5.3 GPM
  • Chemical Injection Knob: Increases or decreases the foam output
  • Replaceable Filter: Prevents grit from entering the soap stream
  • Adjustable Fan Blades: Changes the jet spray from narrow to wide

Specifications: 

  • Min. Pressure: 1,100 psi
  • Max. Pressure: 4,000 psi
  • Min. Flow: 1.8 gpm
  • Max Flow: 5.3 gpm
  • Max Temp: 140°F
  • Weight: 1.5 lb
  • Manufacturer: MTM Hydro
  • Made in: Italy

Contents:

  • Italian Brass Foam Cannon body
  • Italian Calibrated 32 oz White Bottle
  • 1/4"" x 9"" tube for drawing chemical
  • 3.5 Orifice (1.25mm) installed in the Foamer Body
  • 3.0 Orifice (1.1mm) included with kit
  • Fitting pack (2-pieces) containing a 1/4" M22 adaptor and 1/4" QC Plated Steel Plug
  • Manual with care instructions and exploded view 

Directions:

  • Pour snow soap of your choice into canister (Consult the product information of the Snow Soap you use for amount to pour in canister)
  • It is recommended that pressure washer regulator be adjusted to a lower pressure at initial cannon installation and then adjusted to reach optimal performance
  • Concentration & consistency of foam depend upon type and concentration of detergent used as well as the flow/discharge of the pressure washer
  • After use run clean water through the system and completely rinse the spray head and detergent bottle and suction tube with clean, clear water to assure correct operation and an extremely long life

 

*NOTE*

 A specific 1/4" Male plug may be required in order to attach the QC plug to the end of some residential pressure washer setups. MTM Hydro 1/4" plugs are standard for industrial use but many residential pressure washers such as Generac, Greenworks, Ryobi, AR Blue Clean,etc... have certain models where the coupler will not receive an MTM plug. Not all of these brands are impacted, just certain models. If you look closely, the Chamfer at the end of an MTM plug as well as the neck is, 1.5mm shorter than some couplers may allow. We now offer this new Low Profile QC plugOnce you install the correct plug in your new MTM Foam Cannon, you will see that it was worth finding this specialized fitting as these foam cannons are second to none, even when manufacturers try to change their fittings!

 

Customers Also Viewed